266 materials
Ti-6Al-4V printed by laser powder bed fusion is the alpha-beta titanium alloy built layer by layer from fine powder, melted by a laser under inert gas. Rapid solidification produces a fine acicular martensitic microstructure, often with columnar prior beta grains along the build direction, so as-built parts are strong but less ductile and somewhat anisotropic. Parts retain residual stress, need supports and have a rough surface, so they usually receive stress relief, machining and often hot isostatic pressing. Typical uses are lightweight aerospace brackets, lattice structures and medical and industrial hardware.
3D Systems LaserForm Ti Gr5 (A) is a Ti-6Al-4V grade for laser powder bed fusion, melted layer by layer from fine powder under inert gas. Rapid solidification produces fine acicular martensite in columnar prior-beta grains aligned with the build direction, so as-built parts are strong but of limited ductility and somewhat anisotropic. Parts carry high residual stress and are usually stress relieved before support removal. They are often hot isostatically pressed to close porosity and improve fatigue life, and machined where the rough as-built surface matters. Typical uses are lightweight aerospace brackets, lattice-structured medical implants and complex motorsport and industrial components. Every value on this page is read from 3D Systems' own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
3D Systems LaserForm Ti Gr5 (A) is that maker's Ti-6Al-4V grade, printed by laser powder bed fusion and then hot isostatically pressed. As built, it forms fine acicular martensite within columnar prior-beta grains along the build direction, with high residual stress, some internal porosity and a rough, support-marked surface. Hot isostatic pressing closes internal pores and transforms the martensite to a coarser lamellar alpha-beta structure, giving higher ductility and fatigue resistance at some cost in strength. Surface-connected defects remain, so critical surfaces are usually machined. Parts are used for aerospace brackets, fatigue-loaded components and medical implants. Every value on this page is read from 3D Systems' own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
3D Systems LaserForm Ti Gr5 (A) is that maker's grade of Ti-6Al-4V for laser powder bed fusion, here in the stress-relieved condition. As built, it forms columnar prior-beta grains along the build direction filled with fine acicular martensite, with high residual stress and limited ductility. Stress relief lowers residual stress and partly decomposes the martensite, reducing distortion when parts are cut from the plate, though some anisotropy between build directions remains. Overhangs need supports, the rough surface is usually machined, and fatigue-critical parts are often hot isostatically pressed. Uses include lightweight aerospace brackets, lattice structures and complex titanium parts. Every value on this page is read from 3D Systems' own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
Ti-6Al-4V printed by laser powder bed fusion and annealed at 1050 °C is the alpha-beta titanium alloy in a heat-treated state well above ordinary stress relief. As built, it has a fine martensitic alpha-prime structure, columnar prior-beta grains, residual stress and a rough surface that needs supports. Annealing relieves the stress and converts the martensite to a coarser alpha-plus-beta structure, trading some strength for ductility, but it does not close internal pores. Parts serve in aerospace brackets, lightweight lattice structures and medical components.
Ti-6Al-4V made by laser powder bed fusion and annealed at 704 °C is the alpha-beta titanium alloy in a stress-relieved condition. As printed, the rapid melting and cooling leave a fine acicular martensitic microstructure, high residual stress, some anisotropy between build directions, and a rough surface, with supports needed. The anneal relieves most of the residual stress and starts to break down the martensite into an alpha-beta structure, improving ductility and dimensional stability. It does not close porosity or smooth the surface, so hot isostatic pressing or machining is often added for fatigue-critical parts. Typical uses are aerospace brackets and lightweight structural parts.
Ti-6Al-4V printed by laser powder bed fusion and annealed at 740 °C is the alpha-beta titanium alloy in a stress-relieved condition. As built, rapid cooling gives a fine martensitic alpha-prime structure in columnar prior-beta grains, with high residual stress, build-direction anisotropy and a rough surface. Annealing relieves most of the stress and decomposes the martensite into alpha plus beta, which usually improves ductility at some cost in strength. It does not close pores or smooth the surface, so hot isostatic pressing and machining remain common for fatigue-critical parts. Typical uses are aerospace brackets, medical devices and lightweight industrial hardware.
Colibrium Additive Ti6Al4V Grade 5 is that maker's Ti-6Al-4V processed by laser powder bed fusion, here in the as-built condition before any heat treatment. Rapid solidification of the melt pool gives a fine acicular alpha-prime martensite within columnar prior-beta grains elongated along the build direction. As a result, strength is high, ductility is limited and properties differ between build directions. As-built parts carry high residual stress, rough surfaces and support structures, so they are normally stress relieved or hot isostatically pressed, removed from the plate and machined on critical faces. Typical uses are lightweight aerospace brackets and housings, medical device components and lattice structures. Every value on this page is read from Colibrium Additive's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
Colibrium Additive Ti6Al4V Grade 5 is that maker's Ti-6Al-4V powder grade, printed by laser powder bed fusion and given a stress-relief heat treatment. As built, the rapid solidification produces fine acicular martensite within columnar prior-beta grains elongated along the build direction, with high residual stress and directional properties. Stress relief, usually done while parts are still on the build plate and before support removal, reduces residual stress and distortion and partly decomposes the martensite, but it does not close internal porosity. Parts typically still need support removal and machining or finishing of the rough as-built surfaces. Printed parts serve as lightweight aerospace brackets and housings, medical device components and complex industrial parts. Every value on this page is read from Colibrium Additive's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
EOS Titanium Ti64 Grade 5 is a Ti-6Al-4V grade for laser powder bed fusion, in which a laser melts the alloy powder layer by layer under inert gas. Rapid solidification leaves fine acicular martensite within columnar prior-beta grains along the build direction, with high residual stress and some anisotropy. Parts are normally stress-relieved before removal from the plate and supports. They are often hot isostatically pressed to close porosity and improve ductility and fatigue strength, and fatigue-critical surfaces are machined. Printed parts serve as lightweight aerospace brackets, medical implant components and complex industrial parts. Every value on this page is read from EOS's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
EOS Titanium Ti64 Grade 5, heat-treated, is Ti-6Al-4V powder from EOS that has been built by laser powder bed fusion and then heat-treated. As built, the alloy forms columnar prior-beta grains along the build direction, filled with fine acicular martensite, and it carries high residual stress and limited ductility. Heat treatment relieves those stresses and turns the martensite into a fine lamellar alpha-beta structure, which raises ductility at some cost in strength. The columnar grains and any internal porosity remain. Parts still need support removal and surface finishing, and are used for lightweight aerospace brackets, motorsport parts and lattice structures in medical devices. Every value on this page is read from EOS's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
Farsoon Ti6Al4V is Farsoon's grade of Ti-6Al-4V powder for laser powder bed fusion, where a laser melts the alloy layer by layer under inert gas. Rapid cooling gives a fine martensitic alpha-prime structure in columnar prior-beta grains along the build direction, so as-built parts are strong but of limited ductility and somewhat anisotropic. High residual stress means parts are stress relieved before removal from the plate, and hot isostatic pressing is often added to close porosity and coarsen the structure for fatigue. Supports are then cut away and rough surfaces machined. Printed parts serve as lightweight aerospace brackets, lattice-structured medical implants and motorsport components. Every value on this page is read from Farsoon's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
Farsoon Ti6Al4V, heat-treated, is that maker's grade of Ti-6Al-4V titanium alloy printed by laser powder bed fusion and heat treated after the build. As printed, the alloy has columnar prior-beta grains along the build direction filled with fine acicular martensite, high residual stress and limited ductility. Heat treatment relieves the stress and decomposes the martensite into a fine alpha-beta structure, improving ductility at some cost in strength, though it does not close internal porosity. Parts need supports and machining or finishing of the rough surface. Typical uses are lightweight aerospace brackets, medical device components and other complex high-performance parts. Every value on this page is read from Farsoon's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
Ti-6Al-4V made by laser powder bed fusion and hot isostatically pressed at 800 °C is the printed alpha-beta titanium alloy in a densified, stress-relieved condition. As built, it has a fine martensitic microstructure, columnar prior-beta grains along the build direction, residual stress, orientation-dependent properties and rough surfaces. HIP closes internal pores, relieves residual stress and decomposes the martensite into a finer alpha-beta structure. Surface-connected pores and the rough as-built finish remain, so machining or surface finishing is usually still needed. Parts in this condition are used for fatigue-loaded aerospace and medical components where internal defects limit performance.
Ti-6Al-4V made by laser powder bed fusion and then hot isostatically pressed at 926 °C is a printed alpha-beta titanium alloy in its densified condition. As printed, it has fine acicular martensite, columnar prior-beta grains along the build direction, residual stress and some internal pores. Hot isostatic pressing closes internal porosity, relieves residual stress and coarsens the martensite into an alpha-beta structure, improving fatigue performance and ductility at some cost in strength. Surface roughness and surface-connected pores remain, so critical surfaces are usually machined. Parts serve in aerospace structures, medical devices and other fatigue-loaded components.
Ti-6Al-4V made by laser powder bed fusion, then hot isostatically pressed at 926 °C and annealed at 704 °C, is a fully post-processed condition of the printed alloy. As built, it has a fine martensitic microstructure, residual stress, some internal porosity and anisotropy between build directions. Pressing closes most internal pores and converts the martensite to a coarser alpha-beta structure, and the anneal stabilises it, improving ductility and fatigue resistance at some cost in strength. Surface roughness from the process remains, so fatigue-critical surfaces are usually machined or polished. Parts are used for aerospace structures and load-bearing medical hardware.
Ti-6Al-4V made by laser powder bed fusion and vacuum annealed at 800 °C is the common alpha-beta titanium alloy in a stress-relieved condition. As printed, it has a fine martensitic microstructure, high residual stress, some anisotropy between build directions and a rough surface. Vacuum annealing relaxes much of the stress and transforms the martensite toward an alpha-beta structure, improving ductility without the oxygen pickup of heat treatment in air. Internal porosity is not closed, and surfaces usually still need machining. Parts are used for aerospace brackets, medical implants and lightweight structural components.
Velo3D Ti-6Al-4V is Velo3D's grade of the titanium alloy, a powder and parameter set for building parts by laser powder bed fusion. Rapid solidification gives a fine martensitic alpha-prime structure in columnar prior-beta grains along the build direction, with some anisotropy between orientations and high residual stress. Parts are usually stress relieved on the build plate, often hot isostatically pressed to close porosity and improve fatigue strength, and machined where the rough as-built surface and support marks matter. Typical uses are lightweight brackets, manifolds and other complex titanium parts for aerospace, space and high-performance industrial equipment. Every value on this page is read from Velo3D's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
Velo3D Ti-6Al-4V is that maker's grade of the alpha-beta titanium alloy made by laser powder bed fusion, here in the annealed condition. As built, rapid solidification gives columnar prior-beta grains along the build direction filled with fine acicular martensite, plus high residual stress and a rough surface. Annealing relieves the stress and turns the martensite into a fine alpha-beta structure with better ductility, though some anisotropy between build directions remains. Parts are typically machined on critical surfaces and may be hot isostatically pressed for fatigue-loaded service. They serve as lightweight aerospace brackets, ducts, manifolds and other complex titanium components. Every value on this page is read from Velo3D's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
Velo3D Ti-6Al-4V is the maker's grade of Ti-6Al-4V titanium alloy printed by laser powder bed fusion, here in the hot isostatically pressed condition. As built, it forms columnar prior-beta grains along the build direction filled with fine acicular martensite, and it carries residual stress and some internal porosity. HIP closes the internal pores and coarsens the martensite into a lamellar alpha-beta structure, which improves ductility and fatigue life. Surface-connected porosity and the rough as-printed surface remain, so they are usually machined or finished. Printed parts include lightweight brackets, housings and fluid components for aerospace, space and other demanding applications. Every value on this page is read from Velo3D's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
Xact Metal Ti-6Al-4V Grade 5 (Linde) is a Grade 5 titanium alloy powder that Xact Metal offers for laser powder bed fusion. As built, the rapid solidification gives fine acicular martensite inside columnar prior-beta grains elongated along the build direction, which makes properties anisotropic and leaves high residual stress. Parts are usually stress relieved before removal from the build plate, often hot isostatically pressed to close porosity and improve fatigue, and machined where the rough, support-marked surface matters. Printed parts serve as lightweight aerospace brackets and housings, lattice structures and medical device components. Every value on this page is read from Xact Metal's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
Xact Metal Ti-6Al-4V Grade 5 (Linde) is a Grade 5 titanium alloy printed by laser powder bed fusion, here in the stress-relieved condition. As printed, rapid solidification gives a fine acicular martensitic structure in columnar prior-beta grains along the build direction, with high residual stress, rough surfaces and a need for supports. Stress relief, usually done before parts are cut from the build plate, limits distortion and partly tempers the martensite but does not close porosity, so fatigue-critical parts are often also hot isostatically pressed. Typical parts are lightweight aerospace brackets, motorsport components and medical devices. Every value on this page is read from Xact Metal's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
Ti-6Al-4V printed by wire-fed laser directed energy deposition is the alpha-beta titanium alloy built by melting wire feedstock with a laser, bead on bead, into large near-net-shape forms. Parts solidify as coarse columnar prior-beta grains that grow through many layers, so properties differ along and across the build direction. The surface is rough and wavy, and residual stress and distortion are high, so parts usually need stress relief and machining, and inert gas shielding is needed to limit oxygen pick-up. Deposition is fast with little wasted material. Typical uses are large aerospace structural preforms, added features on wrought or forged bodies, and repair.
Meltio Titanium 64 is a Ti-6Al-4V wire feedstock printed by wire-feed laser directed energy deposition, where a laser melts the wire into tracks built up layer by layer under inert gas shielding. Repeated melting and reheating give coarse columnar prior-beta grains elongated along the build direction with a fine lamellar alpha-beta structure inside, so properties differ between build directions. Deposits are near-net shapes with a wavy, rough surface and residual stress, and are normally stress relieved and machined to final dimensions. Typical uses are near-net preforms for machined aerospace and industrial parts, repair of titanium components, and adding features to existing parts. Every value on this page is read from Meltio's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
Meltio Titanium 64 in the as-built condition is Ti-6Al-4V wire deposited by laser wire-feed directed energy deposition and left without heat treatment. Layer-by-layer solidification produces coarse columnar prior-beta grains along the build direction with fine acicular alpha inside, so strength and ductility differ between build directions. Parts carry residual stress and a wavy, stepped surface, so they are near-net shapes that are machined and usually stress relieved before service. Typical uses are large titanium preforms, features added to existing parts and repair of titanium components, often on hybrid machines that deposit and machine in one setup. Every value on this page is read from Meltio's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
Meltio Titanium 64 is Meltio's Ti-6Al-4V wire printed by laser wire-feed directed energy deposition, here in the heat-treated condition. Deposited bead by bead, it forms dense near-net shapes with columnar prior-beta grains along the build direction, fine martensitic alpha laths, residual stress and a rippled surface that is machined off. Heat treatment relieves the stress and transforms the martensite into a more ductile alpha-beta structure, while the columnar grains and their anisotropy largely remain. Typical parts are large titanium preforms and structural components finished by machining, often on hybrid machines, as well as repairs and features added to existing titanium parts. Every value on this page is read from Meltio's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.