Ti-6Al-4V printed by laser powder bed fusion is the alpha-beta titanium alloy built layer by layer from fine powder, melted by a laser under inert gas. Rapid solidification produces a fine acicular martensitic microstructure, often with columnar prior beta grains along the build direction, so as-built parts are strong but less ductile and somewhat anisotropic. Parts retain residual stress, need supports and have a rough surface, so they usually receive stress relief, machining and often hot isostatic pressing. Typical uses are lightweight aerospace brackets, lattice structures and medical and industrial hardware.
Compliance & Regulations
Each row is one condition this material was measured in. Its values and curves are in the tables and charts below, labelled with the condition; the ranges here span that row's own cited values and are never averaged across rows.
| Condition | Yield (MPa) | UTS (MPa) | Elongation (%) | E (GPa) | Fatigue (MPa) | Density (kg/m³) | Values | Curves |
|---|---|---|---|---|---|---|---|---|
| Ti-6Al-4V (L-PBF, stress relieved) | 965 | 1042 | 11.4 | — | — | — | 3 | 0 |
| Farsoon Ti6Al4V, heat-treated | 850 | 950 | 10.0 | — |
10 interactive curves for this material
Stress-strain, S-N fatigue and environmental knockdown curves are free with an account.
Create free account| Property | Value | Unit | Conditions | Source | |
|---|---|---|---|---|---|
Elongation at Break(εf) | 6.100 – 22.80 | % | 51 entriesClick to expand | ||
Fatigue Strength (10⁷ cycles)(σf) | 595.0 | MPa | EOS Titanium Ti64 Grade 5, heat-treated · EOS M 290 | 40 µm · heat-treated · ASTM E466 | ||
Hardness (Rockwell C)(HRC)3 entries | 36.00 range 34.00–38.00 | HRC | 3D Systems LaserForm Ti Gr5 (A), HIP · HIP · ASTM E18 | ||
| ↳ | 40.00 range 38.00–42.00 | HRC | 3D Systems LaserForm Ti Gr5 (A), stress-relieved · stress-relieved · ASTM E18 | ||
| ↳ | 34.60 | HRC | Xact Metal Ti-6Al-4V Grade 5 (Linde), stress-relieved · stress-relieved · ASTM E18 | ||
Hardness (Vickers)(HV)2 entries | 364 | HV | Colibrium Additive Ti6Al4V Grade 5, as-built · Parameter 412 · as-built · XY | ||
| ↳ | 343 | HV | Colibrium Additive Ti6Al4V Grade 5, stress-relieved · Parameter 412 · stress-relieved · XY | ||
Reduction of Area(RA) | 20.00 – 43.00 | % | 16 entriesClick to expand | ||
S–N Curve (Wöhler)(S–N)2 entries | Curve (14 pts) | Pa | HIP 800 °C · 20°C · R = −1 · 100 Hz · rotating bending · machined and polished, as-built surface and contour removed surface · HIP 800 °C, 2 h, 200 MPa argon, ~12 °C/min cooling · Z (built vertically) | ||
| ↳ | Curve (16 pts) | Pa | vacuum annealed 800 °C · 20°C · R = −1 · 100 Hz · rotating bending · machined and polished, as-built surface and contour removed surface · 800 °C, 2 h, vacuum furnace (75 mTorr argon), ~12 °C/min cooling · Z (built vertically) | ||
Stress–Strain Curve(σ–ε) | — | Pa | 8 entriesClick to expand | ||
Ultimate Tensile Strength(σUTS) | 0.9030 – 1.345 | GPa | 51 entriesClick to expand | ||
Yield Strength (0.2% offset)(σy) | 0.7200 – 1.215 | GPa | 51 entriesClick to expand | ||
Young's Modulus(E) | 100.0 – 156.7 | GPa | 21 entriesClick to expand | ||
| Property | Value | Unit | Conditions | Source | |
|---|---|---|---|---|---|
Melting Point / Solidus(Tm)2 entries | 1,968.2 range 1,965.2–1,971.2 | K | 3D Systems LaserForm Ti Gr5 (A) | ||
| ↳ | 2,178.7 range 2,151.2–2,206.2 | K | Xact Metal Ti-6Al-4V Grade 5 (Linde) · General Wrought Material Data | ||
Thermal Conductivity(k)2 entries | 6.700 | W/(m·K) | 3D Systems LaserForm Ti Gr5 (A) · 50°C | ||
| ↳ | 7.200 | W/(m·K) | Xact Metal Ti-6Al-4V Grade 5 (Linde) · General Wrought Material Data | ||
Coefficient of Thermal Expansion(α (CTE))4 entries | 0.00000860 | 1/K | 3D Systems LaserForm Ti Gr5 (A) · 100°C | ||
| ↳ | 0.00000900 | 1/K | EOS Titanium Ti64 Grade 5 · 100°C · EOS M 290 | 40 µm · ASTM E228 | ||
| ↳ | 0.00000940 | 1/K | EOS Titanium Ti64 Grade 5 · 200°C · EOS M 290 | 40 µm · ASTM E228 | ||
| ↳ | 0.00000970 | 1/K | EOS Titanium Ti64 Grade 5 · 300°C · EOS M 290 | 40 µm · ASTM E228 |
| Property | Value | Unit | Conditions | Source | |
|---|---|---|---|---|---|
Density(ρ) | 4.386 – 4.430 | kg/m³ | 9 entriesClick to expand | ||
Reference data from cited sources. Not verified or certified by MatWorld Inc. Verify against the source before use in design. Terms: engineering data
| — |
| — |
| 3 |
| 0 |
| Farsoon Ti6Al4V | — | — | — | — | — | 4400 | 1 | 0 |
| Ti-6Al-4V (L-PBF, as-built) | 1045 | 1106 | 7.6 | 109 | — | — | 4 | 0 |
| Velo3D Ti-6Al-4V, annealed | 775–891 | 950–1045 | 12.0–20.0 | 101–113 | — | — | 20 | 0 |
| Colibrium Additive Ti6Al4V Grade 5, stress-relieved | 950–975 | 1050–1055 | 15.5–16.5 | 113–119 | — | — | 31 | 0 |
| Velo3D Ti-6Al-4V | — | — | — | — | — | 4430 | 1 | 0 |
| EOS Titanium Ti64 Grade 5 | — | — | — | — | — | 4400 | 4 | 0 |
| Velo3D Ti-6Al-4V, HIP | 720–840 | 910–1001 | 13.5–19.8 | 100–122 | — | — | 20 | 0 |
| Xact Metal Ti-6Al-4V Grade 5 (Linde) | — | — | — | — | — | — | 2 | 0 |
| Xact Metal Ti-6Al-4V Grade 5 (Linde), stress-relieved | 903–931 | 1007–1014 | 6.1–12.5 | — | — | 4410 | 8 | 0 |
| 3D Systems LaserForm Ti Gr5 (A) | — | — | — | — | — | 4420 | 4 | 0 |
| 3D Systems LaserForm Ti Gr5 (A), stress-relieved | 1030–1130 | 1110–1210 | 7.0–11.0 | 105–120 | — | — | 8 | 0 |
| 3D Systems LaserForm Ti Gr5 (A), HIP | 880–960 | 970–1070 | 11.0–18.0 | 105–120 | — | — | 8 | 0 |
| Colibrium Additive Ti6Al4V Grade 5, as-built | 1170–1215 | 1315–1345 | 6.5–9.0 | 110–113 | — | — | 31 | 0 |
| EOS Titanium Ti64 Grade 5, heat-treated | 970–1070 | 1080–1150 | 12.0–15.0 | — | 595 | — | 17 | 0 |
| HIP 926 °C | 1008–1042 | 1070–1096 | 15.9–17.5 | — | — | 4404–4416 | 4 | 1 |
| annealed 704 °C | 927–1200 | 1012–1230 | 7.4–13.0 | — | — | 4386–4394 | 13 | 4 |
| annealed 740 °C | 927–964 | 990–1014 | 9.0–13.0 | — | — | — | 9 | 1 |
| HIP 800 °C | 998–1018 | 1083–1094 | 15.3–22.8 | 150–157 | — | — | 4 | 1 |
| annealed 1050 °C | 799–832 | 903–941 | 11.0–14.0 | — | — | — | 9 | 1 |
| HIP 926 °C + annealed 704 °C | 1030–1048 | 1080–1098 | 15.0–17.2 | — | — | 4395–4405 | 4 | 1 |
| vacuum annealed 800 °C | 979–1013 | 1079–1091 | 11.5–17.8 | 149–151 | — | — | 4 | 1 |
Machines the manufacturer states for this material.