103,444 materials
P6 Mn3 Pd20 is an intermetallic compound combining palladium, manganese, and phosphorus in a crystalline structure. This is a research-phase material within the broader family of transition-metal phosphides and palladium intermetallics, with potential applications in catalysis, electronics, and magnetic materials where the combination of noble-metal stability and multivalent transition-metal activity offers promise over conventional alternatives.
P6 N10 is a semiconductor material, likely a nitride-based compound from the III-V or related semiconductor families, though its exact composition is not publicly specified in standard references. This material is typically investigated for high-frequency, high-power, or high-temperature electronic applications where wide bandgap semiconductors offer advantages over conventional silicon. The nitride designation suggests potential use in RF power devices, optoelectronics, or harsh-environment sensing where thermal stability and electrical performance under demanding conditions are critical.
P6 Rb4 is an experimental semiconductor compound composed of rubidium and a primary group VI or pnicogen element, representing a material in the layered or structurally novel class of semiconductors under active research. This composition falls within the broader family of post-transition metal semiconductors and potentially exhibits properties relevant to solid-state electronics, photovoltaics, or thermoelectric applications. Such materials are studied primarily in academic and advanced materials research settings rather than mainstream industrial production, with potential future applications in next-generation optoelectronics or energy conversion devices if scalability and performance targets can be met.
P6 S18 Zn4 is a zinc-containing semiconductor compound, likely a phosphide or sulfide-based material with zinc doping or alloying. This composition suggests a research or specialty material within the broader family of III-V or II-VI semiconductors, potentially developed for optoelectronic or photovoltaic applications where zinc incorporation modifies bandgap, carrier mobility, or defect passivation properties. The material's specific designation and limited commercial visibility indicate it may be an experimental composition or a niche product used in advanced research settings rather than high-volume industrial manufacturing.
P6 Sn2 is a tin-based semiconductor compound, likely a intermetallic or doped semiconductor material in the tin-rich region of a phase system. This composition suggests research-stage material development, as it is not a widely commercialized semiconductor in mainstream electronics. The material would be of interest in emerging applications requiring tin-based semiconducting behavior, such as alternative channel materials for low-dimensional devices, thermoelectric studies, or specialized optoelectronic research where tin compounds offer advantages over conventional silicon or III-V semiconductors.
P6 Sr2 is a strontium-containing semiconductor compound, likely belonging to the perovskite or related crystal structure family based on its designation. While specific composition details are not provided, strontium-based semiconductors are primarily investigated in research settings for optoelectronic and photovoltaic applications, where their tunable bandgap and ionic properties offer potential advantages over conventional semiconductors. This material represents an emerging class of compounds rather than an established commercial product, with development focused on thin-film devices, radiation detection, and next-generation energy conversion technologies.
P8 is a semiconductor material with a composition not yet specified in this database entry. Based on the designation, it likely belongs to a phosphide or pnictide semiconductor family commonly explored in optoelectronic and high-frequency device research. The material's elastic properties suggest moderate stiffness suitable for thin-film or heterostructure applications where mechanical stability during processing and integration is important.
P8 Ba6 is a barium-containing semiconductor compound, likely a barium-based intermetallic or ceramic semiconductor material used in specialized electronic and optoelectronic applications. The exact crystal structure and doping chemistry are not specified in available documentation, but barium-rich semiconductors are typically employed where high-temperature stability, specific band-gap properties, or ionic conductivity are required. This material may be of research or niche industrial interest rather than mainstream production use.
P8 Cr2 is a chromium-based semiconductor material, likely a research or specialized compound in the chromium chalcogenide or chromium pnictide family. While specific compositional details are limited in available documentation, chromium-based semiconductors are investigated for their potential in spintronics, magnetic semiconductor devices, and high-temperature electronics applications where conventional silicon approaches face limitations. Engineers consider such materials when designing systems requiring magnetic ordering combined with semiconducting behavior, particularly in emerging device architectures where coupling between electronic and magnetic properties is functionally advantageous.
P8 Cu6 Ba4 is a copper-based intermetallic compound containing barium, likely belonging to a family of metal matrix composites or advanced copper alloys developed for specialized high-performance applications. This appears to be a research or experimental material rather than a widely commercialized grade; compounds in this composition class are typically investigated for electrical conductivity, thermal management, or mechanical property combinations that balance copper's excellent conduction characteristics with the strength or stability contributions of barium-rich phases. Engineers would evaluate this material primarily in contexts where conventional copper alloys or single-phase metals fall short, such as applications requiring enhanced hardness, thermal cycling resistance, or tailored electromagnetic properties.
P8 Ir4 is a semiconductor material based on iridium (Ir) composition, likely an intermetallic compound or iridium-rich alloy engineered for high-performance electronic and photonic applications. This material belongs to the family of refractory metal semiconductors, which are valued for their thermal stability and electronic properties at elevated temperatures. P8 Ir4 is of particular interest in research and specialized industrial contexts where conventional semiconductors reach performance limitations due to temperature or chemical environment constraints.
P8 Mo2 is a molybdenum-containing tool steel or hardened steel alloy, likely a powder metallurgy or premium grade variant formulated for high-performance cutting, forming, or wear-resistant applications. This material combines molybdenum's hardness and heat resistance with iron-base metallurgy to deliver superior toughness and thermal fatigue resistance compared to standard tool steels, making it suitable for demanding industrial processes where thermal cycling and abrasive wear are significant concerns.
P8 N12 O2 is a phosphorus-nitrogen-oxygen ceramic compound, likely representing a phosphorus nitride or phosphoramide-based ceramic material. This composition family is primarily investigated in materials research for high-temperature applications and specialty ceramic components where thermal stability and chemical resistance are critical. The material is notable for its potential in extreme environment applications where traditional oxides may be limited, though commercial adoption remains limited compared to established ceramic systems like alumina or silicon nitride.
P8 N8 F16 is a ceramic material with a composition not yet specified in the database; the designation suggests a phosphate, nitride, or fluoride-based ceramic system, likely developed for specialized high-temperature or chemical-resistance applications. Without confirmed composition data, this appears to be either a research-phase ceramic compound or a proprietary formulation used in niche industrial settings. Engineers should consult material suppliers or technical datasheets to confirm phase composition, processing method, and performance characteristics before specifying for critical applications.
P8N8O8 is a phosphorus-nitrogen-oxygen ceramic compound belonging to the phosphate nitride family, a class of materials explored for their potential thermal stability and chemical resistance. This appears to be a research-phase composition rather than a commercial ceramic; materials in this chemical family are investigated primarily for high-temperature applications and specialized coating systems where conventional oxides show limitations. The phosphate nitride class offers potential advantages in thermal shock resistance and oxidation protection, though widespread industrial adoption remains limited compared to established ceramics like alumina or silicon nitride.
P8O12 is a phosphorus-oxygen ceramic compound, likely a phosphate or polyphosphate ceramic with potential applications in refractory and thermal management systems. This material family is primarily investigated for high-temperature stability, thermal insulation, and chemical resistance in specialized industrial environments where conventional ceramics may degrade.
P8 O20 is a phosphorus-oxygen ceramic compound, likely a phosphate-based ceramic material belonging to the broader family of phosphate ceramics used in specialized engineering applications. This material class is employed where chemical resistance, thermal stability, or biocompatibility is required, and is particularly valued in applications demanding resistance to acidic environments or requiring controlled dissolution properties that distinguish it from traditional silicate ceramics.
P8 Pd8 S8 is a palladium-sulfur compound semiconductor with potential applications in catalysis and electronic devices, though this specific stoichiometry is not widely documented in mainstream engineering literature and may represent an experimental or niche research composition. Materials in the palladium-sulfur family are explored for catalytic properties, especially in hydrogen storage, desulfurization processes, and solid-state electronics, where palladium's high electrochemical activity and sulfur's coordination chemistry offer advantages over more conventional semiconductors. Engineers would consider such compounds when seeking alternatives to traditional semiconductors in niche applications requiring catalytic function or when palladium's chemical robustness and thermal stability justify cost.
P8 Pd8 Se8 is an experimental chalcogenide semiconductor compound combining palladium and selenium in a defined stoichiometric ratio, representing a member of the metal chalcogenide family of materials. This composition falls within research-stage materials being investigated for optoelectronic and thermoelectric applications, where the palladium-selenium system offers potential advantages in bandgap engineering and carrier transport properties compared to conventional binary semiconductors.
P8 Pt4 is a platinum-based semiconductor compound, likely a platinum-rich intermetallic or chalcogenide phase used in specialized electronic and thermoelectric applications. This material is notable in research contexts for its high thermal and electrical conductivity combined with semiconducting behavior, making it relevant for high-temperature electronics and energy conversion devices where conventional semiconductors would fail.
P8 Rh4 is a rhodium-containing semiconductor compound, likely a phosphide or related intermetallic phase with significant rhodium doping. This material represents research-level development in the semiconductor family, potentially targeted at high-performance electronic or optoelectronic applications where rhodium's catalytic properties and high thermal stability can be leveraged. The material is notable for combining semiconductor functionality with the corrosion resistance and thermal properties associated with noble metal doping, making it relevant for harsh-environment electronics or advanced thermoelectric/photonic devices where conventional semiconductors are insufficient.
P8 S10 is a semiconductor material, likely a phosphorus-silicon compound or related III-V/IV semiconductor alloy, though the specific composition requires clarification from suppliers. This material family is typically investigated for optoelectronic and high-frequency electronic applications where tunable bandgap properties or specific lattice parameters offer advantages over conventional silicon or compound semiconductors.
P8 S32 Dy8 is a rare-earth doped semiconductor compound likely belonging to the dysprosium-containing oxide or intermetallic family, based on its designation. While specific compositional details are not provided in standard references, this material represents an emerging class of rare-earth semiconductors studied for applications requiring specific electronic, magnetic, or optical properties that benefit from dysprosium doping. Engineers would consider this material for specialized applications where rare-earth elements provide advantages such as enhanced luminescence, magnetic coupling, or thermal stability that conventional semiconductors cannot match.
P8 S32 Er8 is a rare-earth doped semiconductor material, likely a crystalline compound incorporating erbium as a primary dopant within a phosphide or sulfide host lattice. This designation suggests a research or specialized optical semiconductor composition used in photonic and optoelectronic device development. Materials in this family are investigated for infrared emission, quantum dot applications, and integrated photonics where rare-earth luminescence provides wavelength selectivity and signal processing capabilities unavailable in conventional semiconductors.
P8 S32 Nd8 is a neodymium-containing compound or intermetallic material, likely part of a rare-earth or transition-metal family used in functional or structural applications. Without confirmed composition data, this material appears to be either a specialized research compound or a proprietary alloy designation; neodymium-bearing systems are typically engineered for magnetic, optical, or high-temperature performance.
P8 S32 Pr8 is a rare-earth doped semiconductor material, likely a phosphor or scintillator compound based on its designation nomenclature. This material belongs to the family of rare-earth activated ceramics or glasses commonly engineered for photonic and radiation detection applications. The specific composition suggests a praseodymium-doped system optimized for luminescence or energy conversion in specialized optical and sensing devices.
P8 S32 Sm8 is a samarium-doped semiconductor material, likely a rare-earth compound in the pnictide or chalcogenide family based on its designation. This material family is of significant research interest for advanced electronic and photonic applications where rare-earth dopants enhance magnetic, luminescent, or electronic transport properties. Industrial adoption remains limited, with primary development focused on specialized optoelectronics, magnetism-based devices, and emerging quantum or high-temperature applications where samarium doping provides performance advantages over undoped or alternative rare-earth variants.
P8 S32 Tb8 is a semiconductor material likely belonging to a rare-earth or transition-metal compound family, though its exact composition is not specified in available documentation. This material appears to be a research or specialized compound rather than a widely commercialized semiconductor, and would be evaluated for applications requiring specific electronic or optoelectronic properties inherent to its material class. Engineers would consider this material where conventional semiconductors are insufficient and the material's particular electronic behavior—potentially related to its rare-earth or terbium content—offers advantages for specialized device performance.
P8 S8 appears to be a phosphorus-sulfur compound or alloy, likely a specialized semiconductor or functional material in the phosphorus-sulfur family. While specific composition details are not provided, materials in this class are typically investigated for optoelectronic, photovoltaic, or ion-conducting applications where the combined P-S chemistry offers tailored electronic properties. Engineers would consider this material primarily in emerging technology spaces where conventional semiconductors are insufficient, though adoption depends on scalability and cost-effectiveness relative to established alternatives.
P8 Se20 is a selenium-based semiconductor compound with a nominal composition suggesting an 8:20 stoichiometric ratio, likely in the chalcogenide family of materials. This appears to be a research-phase or specialized semiconductor material used in niche photonic and electronic applications where selenium's unique optical and electronic properties are advantageous. The material is notable for potential applications in infrared optics, photovoltaic research, or specialized thin-film devices where chalcogenide semiconductors offer benefits over conventional silicon—such as extended spectral range, tunable bandgap, or phase-change capabilities.
P8 Sr6 is a strontium-containing semiconductor compound, likely a perovskite or related crystal structure material based on its nomenclature. This material is primarily of research interest for photovoltaic, optoelectronic, or solid-state device applications where strontium doping or incorporation modifies electronic band structure and charge transport properties.
P8 Th6 is a thorium-containing semiconductor compound, likely a research-phase material within the rare-earth or actinide semiconductor family. While thorium-based semiconductors remain primarily experimental, they are investigated for specialized high-temperature, high-radiation environments where conventional semiconductors fail, particularly in nuclear applications and advanced space systems.
P8 U6 is a uranium-based semiconductor compound, likely representing a uranium phosphide or related uranium chalcogenide phase with potential applications in nuclear electronics and specialized radiation-tolerant devices. This material belongs to the family of actinide semiconductors, which are of primary interest in nuclear technology contexts where conventional semiconductors would degrade under radiation exposure. The material's notable advantage lies in its intrinsic radiation hardness and compatibility with nuclear fuel cycle applications, though its practical use remains largely confined to research and specialized defense/nuclear engineering environments due to manufacturing complexity and regulatory constraints.
PA (polyamide) is a semi-crystalline engineering thermoplastic known for its excellent balance of strength, stiffness, and toughness. Widely used in automotive, industrial, and consumer applications, PA offers superior chemical resistance and wear properties compared to commodity plastics, making it the preferred choice for structural components requiring durability and dimensional stability.
Pa1 is a semiconductor material with unspecified composition, likely part of a research or proprietary material family under development. Without compositional detail, this appears to be an experimental compound or a designation for a material system under investigation, possibly within the broader context of advanced semiconductor research for electronic or optoelectronic applications.
PA11 is a semi-crystalline polyamide (nylon) derived from renewable castor oil feedstock, offering a sustainable alternative to petroleum-based polyamides while maintaining good mechanical properties and chemical resistance. It is widely used in automotive fuel systems, flexible tubing, cable jacketing, and consumer goods where its combination of toughness, flexibility, and environmental profile provides advantages over PA6 and PA66. Engineers select PA11 when weight reduction, chemical compatibility with fuels and oils, low-temperature flexibility, and a reduced carbon footprint are priorities, despite typically lower stiffness compared to glass-filled alternatives.
PA11 printed by Multi Jet Fusion is a semi-crystalline polyamide processed as a polymer powder bed, where inkjet-applied fusing and detailing agents control where infrared energy melts each layer. Unfused powder supports the part, so no support structures are needed. Parts are nearly dense with some residual porosity, have a slightly grainy grey surface, and are somewhat anisotropic between the build plane and the build direction. Caked powder is removed by bead blasting or air, and parts can then be dyed or smoothed. Typical uses are functional prototypes and production of tough, flexible parts such as housings, clips, ducting, snap-fits and living hinges.
HP 3D High Reusability PA 11 is HP's PA11 powder for Multi Jet Fusion, a powder bed process that jets a fusing agent onto each layer and a detailing agent at part edges before infrared energy fuses the printed areas, and the grade is formulated so that much of the unfused powder can be reused in later builds. Parts come out grey with a slightly granular surface, need no supports, and are usually bead blasted and often dyed or smoothed. Compared with MJF PA12 they are more ductile and impact resistant, though ductility is lower along the build direction. They are used for snap fits, living hinges and functional parts that must flex repeatedly without cracking. Every value on this page is read from HP's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
PA11 printed by selective laser sintering is a semi-crystalline polyamide made from castor-oil-derived powder, fused layer by layer in a heated powder bed. The surrounding unsintered powder supports the part, so no support structures are needed and many parts can be nested in one build. As-printed parts have a matte, slightly grainy surface, some residual porosity and modest anisotropy between build directions. Parts are depowdered and usually bead blasted, tumbled, dyed or coated. It is used for functional prototypes, snap-fits, living hinges, housings, ducts and impact-loaded end-use parts.
BASF Forward AM Ultrasint PA11 is a PA11 powder grade for selective laser sintering, in which a laser fuses successive layers of polymer powder in a heated bed. The surrounding unfused powder supports the part, so no support structures are needed. Parts come out slightly porous with a matte, grainy surface, and they are weaker and less ductile across the layers than within them; they are depowdered and bead blasted, and often dyed or smoothed. Laser-sintered PA11 is more ductile and impact tolerant than laser-sintered PA12, so it is used for functional prototypes and end-use parts such as snap fits, hinges, housings and ducts. Every value on this page is read from BASF Forward AM's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
BASF Forward AM Ultrasint PA11 is a PA11 powder grade for selective laser sintering, here in the dry as moulded condition, without moisture conditioning after printing. The laser sinters the powder layer by layer in a heated bed, giving semi-crystalline parts with slight residual porosity, a grainy surface and lower ductility in the build direction than in the build plane. Loose powder supports the part, so no support structures are needed, and parts are usually depowdered, bead blasted and often dyed or smoothed. Printed parts serve where impact resistance and elongation matter, such as snap fits, living hinges, ducts, housings and functional prototypes. Every value on this page is read from BASF Forward AM's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
EOS PA 1101 is an unfilled PA11 powder grade printed by selective laser sintering, in which a laser fuses successive layers of polyamide powder in a heated bed. The surrounding unfused powder supports the part, so no support structures are needed. Parts have slight porosity and a matte, grainy surface that is usually bead blasted and may be dyed or smoothed. Elongation and strength are lower across the layers than within them. Laser-sintered PA11 is more ductile and impact resistant than laser-sintered PA12, which suits it to functional prototypes and end-use parts such as snap fits, living hinges, clips and ducts. Every value on this page is read from EOS's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
EOS PA 1101 is a PA11 powder grade for selective laser sintering, here in the dry as moulded state, meaning tested without conditioning to ambient moisture. Each layer is fused in a heated powder bed, so parts need no supports, but they have slight residual porosity, a matte grainy surface and lower strength and elongation across layers than within them. Compared with laser-sintered PA12 it is notably more ductile and impact-resistant. Parts are usually depowdered and bead-blasted, then dyed or smoothed where appearance matters. It is used for functional parts that must flex or take impact, such as snap fits, living hinges, clips and ducts. Every value on this page is read from EOS's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
EOS PA 1102 Black is a black-pigmented PA11 powder grade for selective laser sintering, which gives parts that are coloured through their full cross-section. The parts are built without supports in the powder bed. They come out with a grainy matte surface, some residual porosity, and lower strength and elongation in the build direction than in the build plane. Post-processing is usually depowdering and bead blasting, with smoothing or sealing where needed. Laser-sintered PA11 is more ductile and impact-resistant than PA12, so the grade suits functional prototypes and end-use parts such as snap fits, living hinges, clips, housings and ducts. Every value on this page is read from EOS's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
EOS PA 1102 Black is a black-pigmented PA11 powder grade for selective laser sintering, described here in the dry state. Parts build in a heated powder bed that supports them, so no support structures are needed. They come out slightly porous with a matte, grainy surface, usually cleaned by blasting. As with other laser-sintered polyamides, strength and elongation are lower in the build direction than in the build plane. Compared with laser-sintered PA12, the PA11 base gives more ductile, impact-resistant parts, suited to snap fits, living hinges, clips, ducts and housings, where the through colour avoids dyeing. Every value on this page is read from EOS's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
Formlabs Nylon 11 Powder is a PA11 grade for selective laser sintering, here in the conditioned state, with printed parts equilibrated to ambient moisture. The laser fuses each layer in a powder bed that supports the part, so no supports are needed. Parts have a matte, grainy surface, some porosity and somewhat lower strength and ductility along the build direction, and are depowdered and usually bead blasted. Absorbed moisture plasticizes the polyamide, lowering stiffness and raising toughness and elongation relative to dry parts. Chosen over SLS PA12 for ductility and impact resistance, it is used for snap fits, living hinges, clips, ducts and housings that must flex or absorb impact. Every value on this page is read from Formlabs' own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
PA12 is a semi-crystalline polyamide (nylon) thermoplastic commonly produced through ring-opening polymerization of ε-caprolactam. It is widely used in automotive, consumer goods, and industrial applications where a balance of mechanical strength, chemical resistance, and processing flexibility is required. PA12 is valued for its toughness and fatigue resistance compared to PA6, along with superior dimensional stability in humid environments, making it the preferred choice when moisture sensitivity and long-term performance are critical design constraints.
PA12 printed by fused deposition modeling is a semi-crystalline polyamide thermoplastic, fed as filament and deposited through a heated nozzle, typically on industrial systems with a heated build chamber. The process leaves a layered structure with visible road lines, small voids between beads and weaker bonding between layers than along the deposited paths, so strength and elongation are lowest in the build direction. Warping from uneven cooling is controlled with bed adhesion and chamber temperature, and overhangs need removable support. Parts are used for jigs, fixtures, functional prototypes, housings and ducts needing toughness and chemical resistance.
Stratasys FDM Nylon 12 is a PA12 filament grade printed by fused deposition modeling, here in the as-built condition. Parts are built from extruded roads fused layer by layer, so strength and toughness are lower across layers than within them, and small voids can remain between beads. As-built surfaces show layer lines and stair-stepping on curved and inclined faces, and overhangs need support material that is removed after printing. Printed parts are used for tough functional prototypes, snap fits and other repeatedly flexed features, jigs, fixtures and low-volume end-use components. Every value on this page is read from Stratasys' own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
PA12 printed by Multi Jet Fusion is a nylon thermoplastic built in a polymer powder bed, where a fusing agent is jetted onto each layer and infrared energy melts the powder it covers while a detailing agent sharpens the edges. Parts are nearly fully dense with only modest anisotropy between build directions, a slightly grainy matte surface, and a grey tone from the agent. No support structures are needed because unfused powder holds the part, but parts require depowdering and usually bead blasting, with dyeing or vapor smoothing added for appearance or sealing. Typical uses are functional prototypes, enclosures, housings, ducts, clips, hinges, jigs and low to medium volume production parts.
HP 3D High Reusability PA 12 is a polyamide 12 powder grade for Multi Jet Fusion, in which a fusing agent jetted onto each powder layer absorbs infrared energy so the part areas fuse, and it is formulated so that much of the unfused powder can be reused in later builds. The surrounding powder supports the parts, so no support structures are needed. Parts come out grey with a slightly grainy surface, are normally depowdered and bead blasted and often dyed black, and have fairly even properties across build directions with some residual porosity. Printed parts serve as functional prototypes and end-use parts such as housings, brackets, clips, ducts, and jigs and fixtures. Every value on this page is read from HP's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
HP 3D High Reusability PA 12 W is a white-printing grade of PA12 powder for Multi Jet Fusion, in which infrared energy fuses the powder bed wherever a fusing agent has been jetted, with a detailing agent sharpening edges. Parts come out white rather than the grey typical of the process. They are built without supports in the surrounding powder and show fairly uniform properties across build directions with a slightly grainy surface. They are usually cooled, depowdered and bead blasted, then may be dyed, painted or smoothed. The grade is used for functional prototypes and end-use parts such as housings, enclosures, brackets and consumer components where a light or coloured finish matters. Every value on this page is read from HP's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
PA12 printed by selective laser sintering is a semi-crystalline nylon built from fine powder fused layer by layer in a heated powder bed. The laser sinters the particles rather than fully melting them, so parts keep some residual porosity and a matte, slightly grainy surface, and strength and ductility are usually lowest along the build direction. Surrounding unfused powder supports the part, so no support structures are needed and many parts can be nested in the same build. Parts come out needing depowdering and are often bead blasted, tumbled or dyed to improve finish. Typical uses are functional prototypes, housings, ducts, clips, hinges and low-volume end-use parts.
EOS PA 2200 is a white PA12 powder grade for selective laser sintering and one of the most widely used materials in polymer powder bed fusion. The laser fuses each layer in a heated powder bed, and the unfused powder supports the part, so no support structures are needed and parts can be nested throughout the build volume. Parts come out with a matte, slightly grainy surface, some residual porosity and lower elongation in the build direction than in the layer plane. They are usually bead blasted after depowdering and often dyed or smoothed. Typical uses are functional prototypes and small-series end-use parts such as housings, brackets, ducts, clips and fixtures. Every value on this page is read from EOS's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
EOS PA 2200 is a white PA12 powder grade for selective laser sintering, here in the dry as moulded state, before printed parts take up moisture from the air. The laser fuses each powder layer in a heated bed, and the unfused powder supports the part, so no supports are needed and parts can be nested throughout the build. Printed parts are slightly porous with a matte, granular surface that is usually bead blasted after depowdering, and strength and elongation are lower along the build direction than in the layer plane. It is used for functional prototypes and small series of end-use parts such as housings, ducts, clips, snap fits and fixtures. Every value on this page is read from EOS's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
EOS PA 2201 is a general-purpose white PA12 powder for selective laser sintering, in which a laser fuses successive layers of powder in a heated bed. The surrounding unfused powder supports the parts, so no support structures are needed and parts can be nested throughout the build. As-built parts carry some residual porosity, a grainy matte surface, and somewhat lower strength and elongation along the build direction than in the layer plane. They are usually depowdered and bead blasted, and may be dyed, smoothed or infiltrated. The grade is used for functional prototypes and small series of end-use parts such as housings, ducts, clips, brackets, jigs and fixtures. Every value on this page is read from EOS's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
EOS PA 2201 is an unfilled white PA12 powder grade for selective laser sintering, here in the dry-as-moulded state, before the parts take up moisture from the air. The powder is fused layer by layer in a heated bed whose unfused powder supports the part, so no supports are needed and parts can be nested through the build volume. As built, parts are slightly porous, have a matte, grainy surface, and are weaker and less ductile across layers than within them. They are usually depowdered and bead blasted, and may be dyed or infiltrated. Typical uses are functional prototypes and low-volume end-use parts such as housings, ducts, snap fits and fixtures. Every value on this page is read from EOS's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
Farsoon FS3300PA is a PA12 powder grade made by Farsoon for selective laser sintering, in which a laser fuses successive layers of a heated polymer powder bed. As with other laser-sintered PA12, the surrounding unfused powder supports the parts, so no support structures are needed. Parts retain some porosity, a grainy matte surface, and lower strength and elongation in the build direction than in the layer plane. Printed parts are depowdered and bead-blasted, and may be dyed or smoothed. The grade is used for functional prototypes and end-use parts such as housings, ducts, brackets, clips and fixtures, often in small production runs. Every value on this page is read from Farsoon's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
Formlabs Nylon 12 Powder is a PA12 grade for selective laser sintering, in which a laser fuses heated polymer powder layer by layer into tough, semi-crystalline nylon parts. As printed, parts have some residual porosity, a matte, slightly grainy surface, and somewhat lower strength and elongation across layers than within them. Unsintered powder supports the part, so no supports are needed. Post-processing is mainly depowdering and media blasting, sometimes followed by dyeing or smoothing. Parts are used for functional prototypes and low-volume end-use components such as housings, ducts, snap fits, jigs and fixtures. Every value on this page is read from Formlabs' own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
Formlabs Nylon 12 Powder is a PA12 grade for selective laser sintering, here in the conditioned state, with printed parts equilibrated to a standard laboratory atmosphere. Sintering in a heated powder bed leaves a grainy matte surface, some residual porosity and lower ductility along the build direction. The loose powder supports the part, so no support structures are needed, and parts are depowdered and usually bead blasted. Conditioning lets the polyamide reach its equilibrium moisture content, making it slightly less stiff and more ductile than dry as-printed parts. Parts are used for functional prototypes, jigs and fixtures, enclosures, snap fits and low-volume end-use components. Every value on this page is read from Formlabs' own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.