PEI (FDM) — Properties & Data | MatWorld

PEI (FDM)

PEI printed by fused deposition modeling is polyetherimide, an amorphous high-temperature thermoplastic, extruded as filament and deposited layer by layer. It needs a hot nozzle, a heated bed and usually a heated chamber, since poor thermal control causes warping and weak layer bonding. Parts are anisotropic, weakest across the layer interfaces, with visible layer lines and small voids between deposited roads, and overhangs need supports that are removed afterward. Printed PEI is used for heat-resistant jigs, fixtures, tooling, ducting and brackets, and for functional prototypes and low-volume parts in aerospace, automotive and electronics.

heat-resistant jigsheat-resistant fixturestoolingductingbracketsfunctional prototypes

Compliance & Regulations

?UL 94?ITAR?EAR?ISO 10993?Conflict Free?FDA?RoHS?REACH

PEI/PEI (FDM)

Conditions

Roboze ULTEM AM9085F, conditioned Roboze ULTEM AM9085F Stratasys ULTEM 1010 resin Stratasys ULTEM 9085 resin

Measured as printed

Each row is one condition this material was measured in. Its values and curves are in the tables and charts below, labelled with the condition; the ranges here span that row's own cited values and are never averaged across rows.

Condition	Yield (MPa)	UTS (MPa)	Elongation (%)	E (GPa)	Density (kg/m³)	Values	Curves
Roboze ULTEM AM9085F, conditioned	—	66–89	4.1–6.9	2–3	—	17	0
Roboze ULTEM AM9085F	—	—	—	—	1270	4

Units:

si imperial

Filter by

Statistic

Condition

Source

Table

Temperature

Orientation

Specification

Property	Value	Unit	Conditions
Compressive Modulus(Ec)	1.750 – 3.230	GPa	20 entriesClick to expand
Compressive Strength(σc)	87.80 – 349.0	MPa	18 entriesClick to expand
Elongation at Break(εf)	1.100 – 9.100	%	51 entriesClick to expand
Flexural Modulus(Ef)	1.400 – 3.260	GPa	23 entriesClick to expand
Flexural Strength (MOR)(σf)	48.00 – 144.0	MPa	25 entriesClick to expand
Notched Izod Impact Strength(Izod)	21.70 – 140	J/m	20 entriesClick to expand
Poisson's Ratio(ν)	0.3700	-	Roboze ULTEM AM9085F · 25°C · ASTM D638
Ultimate Tensile Strength(σUTS)	28.20 – 91.60	MPa	27 entriesClick to expand
Yield Strength (0.2% offset)(σy)	35.30 – 92.80	MPa	38 entriesClick to expand
Young's Modulus(E)	1.900 – 4.170	GPa	51 entriesClick to expand

N entriesMultiple entries per property — large groups are collapsed; click a summary row to expand. Use filters above to narrow by form, heat treatment, basis, or test environment.

Verified Unverified Low confidence (<80%) Link to source

Filter by

Statistic

Condition

Source

Table

Temperature

HDT Load

Orientation

Specification

Property	Value	Unit	Conditions
Glass Transition Temperature(Tg)3 entries	482.5	K	Stratasys ULTEM 1010 resin · ASTM D7426
↳	450.5	K	Stratasys ULTEM 9085 resin · Physical Properties - Non Printed, Molded Plaques · ASTM D7426
↳	486.8	K	—
Heat Deflection Temperature(HDT)	443.4 – 490.3	K	11 entriesClick to expand
Melting Point / Solidus(Tm)	391.1	K	—
Thermal Conductivity(k)	0.2095 – 0.2136	W/(m·K)	5 entriesClick to expand
Coefficient of Thermal Expansion(α (CTE))	0.00000429 – 0.0000361	1/K	5 entriesClick to expand

N entriesMultiple entries per property — large groups are collapsed; click a summary row to expand. Use filters above to narrow by form, heat treatment, basis, or test environment.

Rows with are inherited from the base material

Verified Unverified Low confidence (<80%) Link to source

Property	Value	Unit	Conditions	Source
Density(ρ)	1.270	kg/m³	Roboze ULTEM AM9085F · ASTM D792

Verified Unverified Low confidence (<80%) Link to source

Filter by

Statistic

Condition

Table

Orientation

Property	Value	Unit	Conditions	Source
Dielectric Constant (Relative Permittivity)(εr)	2.650 – 3.156	-	12 entriesClick to expand

N entriesMultiple entries per property — large groups are collapsed; click a summary row to expand. Use filters above to narrow by form, heat treatment, basis, or test environment.

Verified Unverified Low confidence (<80%) Link to source

Reference data from cited sources. Not verified or certified by MatWorld Inc. Verify against the source before use in design. Terms: engineering data

Regulatory Screening

Environmental

Export Control

Safety & Biocompatibility

Quality & Standards

Industry-Specific

RoHS, REACH, and Prop 65 statuses are validated against official substance lists (ECHA SVHC Candidate List, OEHHA Prop 65, RoHS Annex II). Other regulations are estimated from composition and material classification. All screening is a starting point for due diligence — always verify with your supplier before making compliance decisions.

PEI (FDM)

Conditions

Measured as printed

Mechanical Properties

Thermal Properties

Physical Properties

Electrical Properties

Regulatory Screening

Environmental

Export Control

Safety & Biocompatibility

Quality & Standards

Industry-Specific

Printed on