3D Systems LaserForm Ti Gr23 (A) is a Ti-6Al-4V ELI (Grade 23) powder grade for laser powder bed fusion, here in the as-built condition without heat treatment. Rapid melt-pool solidification gives fine acicular alpha-prime martensite in columnar prior-beta grains along the build direction, so as-built parts are strong but less ductile than wrought material and anisotropic. Parts carry high residual stress, need supports, and have rough side and downskin surfaces. They are usually stress relieved, often hot isostatically pressed, and machined before use in aerospace, medical and industrial components. Every value on this page is read from 3D Systems' own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.
Compliance & Regulations
| Property | Value | Unit | Conditions | Source | |
|---|---|---|---|---|---|
Elongation at Break(εf)4 entries | 8.000 range 6.000–10.00 | % | DMP FLEX 100 - LT30 · as-built · ASTM E8M · XY | ||
| ↳ | 8.000 range 6.000–10.00 | % | DMP FLEX 100 - LT30 · as-built · ASTM E8M · Z | ||
| ↳ | 9.000 range 6.000–12.00 | % | DMP FACTORY 500 - LT 60 · as-built · ASTM E8 · XY | ||
| ↳ | 11.00 range 9.000–13.00 | % | DMP FACTORY 500 - LT 60 · as-built · ASTM E8 · Z | ||
Reduction of Area(RA)4 entries | 35.00 range 15.00–55.00 | % | DMP FLEX 100 - LT30 · as-built · ASTM E8M · XY | ||
| ↳ | 35.00 range 25.00–45.00 | % | DMP FLEX 100 - LT30 · as-built · ASTM E8M · Z | ||
| ↳ | 23.00 range 12.00–34.00 | % | DMP FACTORY 500 - LT 60 · as-built · ASTM E8 · XY | ||
| ↳ | 32.00 range 28.00–36.00 | % | DMP FACTORY 500 - LT 60 · as-built · ASTM E8 · Z | ||
Ultimate Tensile Strength(σUTS)4 entries | 190 range 168.2–211.8 | ksi | DMP FLEX 100 - LT30 · as-built · ASTM E8M · XY | ||
| ↳ | 185.6 range 175.5–195.8 | ksi | DMP FLEX 100 - LT30 · as-built · ASTM E8M · Z | ||
| ↳ | 190 range 187.1–192.9 | ksi | DMP FACTORY 500 - LT 60 · as-built · ASTM E8 · XY | ||
| ↳ | 187.1 range 181.3–192.9 | ksi | DMP FACTORY 500 - LT 60 · as-built · ASTM E8 · Z | ||
Yield Strength (0.2% offset)(σy)4 entries | 163.9 range 143.6–184.2 | ksi | DMP FLEX 100 - LT30 · as-built · ASTM E8M · XY | ||
| ↳ | 155.2 range 145–165.3 | ksi | DMP FLEX 100 - LT30 · as-built · ASTM E8M · Z | ||
| ↳ | 166.8 range 163.9–169.7 | ksi | DMP FACTORY 500 - LT 60 · as-built · ASTM E8 · XY | ||
| ↳ | 166.8 range 158.8–171.1 | ksi | DMP FACTORY 500 - LT 60 · as-built · ASTM E8 · Z |
| Property | Value | Unit | Conditions | Source | |
|---|---|---|---|---|---|
Density(ρ) | 0.1600 | lb/in³ | — | — |
Reference data from cited sources. Not verified or certified by MatWorld Inc. Verify against the source before use in design. Terms: engineering data