316L Stainless Steel (BMD, Desktop Metal 316L Stainless Steel (Studio System 2), sintered)

UNS S31603· 316L Stainless Steel (Studio System 2)

Desktop Metal 316L Stainless Steel (Studio System 2) is the maker's 316L austenitic stainless steel for bound metal deposition, printed from rods of metal powder in a polymer and wax binder and used in the sintered condition. Parts are extruded oversize, then debound and sintered, shrinking toward near-full density, with a ceramic interface layer letting supports separate after sintering. Sintering rather than melting gives an equiaxed austenitic structure free of melt-induced residual stress, but leaves some porosity, visible layer lines and a surface that often needs machining on critical faces. Parts serve as prototypes, jigs, fixtures and low-volume functional parts. Every value on this page is read from Desktop Metal's own material data sheet — quoted, cited and dated — and is the maker's statement about printed material, not a measurement by MatWorld; none has yet been reviewed by a person.

prototypesjigsfixtureslow-volume functional parts

Compliance & Regulations

?UL 94?ITAR?EAR?ISO 10993?Conflict Free?FDA?RoHS?REACH

316L Stainless Steel (BMD)/316L Stainless Steel (BMD, Desktop Metal 316L Stainless Steel (Studio System 2), sintered)

Units:

si imperial

Property OverviewNormalized to typical max values

Filter by

Table

Specification

Property	Value	Unit	Conditions
Charpy Impact Energy(KV)	219 range 209–229	J	MECHANICAL PROPERTIES IN DESKTOP METAL PURESINTER FURNACE · sintered · MPIF 59
Elongation at Break(εf)2 entries	72.00 range 65.00–79.00	%	MECHANICAL PROPERTIES IN DESKTOP METAL PURESINTER FURNACE · sintered · ASTM E8M
↳	66.00	%	MECHANICAL PROPERTIES SINTERED IN DESKTOP METAL FURNACE · sintered · ASTM E8M
Ultimate Tensile Strength(σUTS)2 entries	84.12 range 83.40–84.85	ksi	MECHANICAL PROPERTIES IN DESKTOP METAL PURESINTER FURNACE · sintered · ASTM E8M
↳	77.31	ksi	MECHANICAL PROPERTIES SINTERED IN DESKTOP METAL FURNACE · sintered · ASTM E8M
Yield Strength (0.2% offset)(σy)2 entries	30.46 range 28.72–32.20	ksi	MECHANICAL PROPERTIES IN DESKTOP METAL PURESINTER FURNACE · sintered · ASTM E8M
↳	24.51	ksi	MECHANICAL PROPERTIES SINTERED IN DESKTOP METAL FURNACE · sintered · ASTM E8M

N entriesMultiple entries per property — large groups are collapsed; click a summary row to expand. Use filters above to narrow by form, heat treatment, basis, or test environment.

Verified Unverified Low confidence (<80%) Link to source

Property	Value	Unit	Conditions	Source
Density(ρ)	0.2811 range 0.2796–0.2825	lb/in³	MECHANICAL PROPERTIES IN DESKTOP METAL PURESINTER FURNACE · sintered

Verified Unverified Low confidence (<80%) Link to source

Reference data from cited sources. Not verified or certified by MatWorld Inc. Verify against the source before use in design. Terms: engineering data

Regulatory Screening

Environmental

Export Control

Safety & Biocompatibility

Quality & Standards

Industry-Specific

RoHS, REACH, and Prop 65 statuses are validated against official substance lists (ECHA SVHC Candidate List, OEHHA Prop 65, RoHS Annex II). Other regulations are estimated from composition and material classification. All screening is a starting point for due diligence — always verify with your supplier before making compliance decisions.

316L Stainless Steel (BMD, Desktop Metal 316L Stainless Steel (Studio System 2), sintered) — Properties & Data | MatWorld